1600 Series Corrosion Resistant Non-Handed Door Closer

Arm Models 1601SS, 1603BCSS, and 1604BCSS

ASSA ABLOY

Installation Instructions

Non-hold Open arm models, adjustable size 1-6 (model 1601SS &) and size 3 & 4 (models 1603BCSS and 1604BCSS).

/ WARNING

This product can expose you to lead which is known to the state of California to cause cancer and birth defects or other reproductive harm.

For more information go to: www.P65warnings.ca.gov.

READ AND FOLLOW ALL INSTRUCTIONS. SAVE THESE INSTRUCTIONS.

1600SS Series Non-Hold Open Closer

ATTENTION:

An incorrectly installed or improperly adjusted door closer can cause property damage or personal injury. These installation instructions should be followed to avoid the possibility of misapplication or misadjustment.

• For special applications, a separate door and frame preparation template is packed with these instructions. Use this instruction sheet for installation sequence and closer adjustments only.
• Doors should be hung on ball bearing or anti-friction hinges.

• A separate door stop is recommended.
• Always consult door/frame manufacturer for fastener compatibility.
• Door and frame must be properly reinforced.
• Adjust closing time speed between 3 and 7 seconds from 90° to 0°.
• These door closers should NOT be installed on exposed side (weather side) of exterior doors.
• Dimensions are given in inches (millimeters).

Supplied Hardware

	Mounting Hardware	Door or Frame	Drill
	Closer, PA Bracket: 1/4-14 x 1-1/2 Oval Flat Head Sheet Metal Screw	Wood/Metal	3/16" (4.8mm) for wood
()MMMM	Closer, PA Bracket: 1/4-20 x 3/4 Oval Flat Head Mach. Screw	Matal	Drill #7 (.201 dia. or 5.1mm) Tap 1/4-20
	Arm Shoe to Jamb or Door: 1/4-20 x 3/4 Round Head Mach. Screw	Metal
	Arm Shoe to Jamb or Door: 1/4-14 x 1-1/2 Round Head Sheet Metal Screw	Wood/Metal	3/16" (4.8mm) for wood
	Closer: Sleeve Nut and Bolt (SNB)	Hollow Metal	9/32" (7.0mm) thru 3/8" (9.5mm) door face opposite to closer
	with 1/4-20 x 3/4 Oval Flat Head Mach. Screw (recommended)	Aluminum or Wood	3/8" (9.5mm) thru
Closer: Thru Bolt and Grommet Nut (TBGN) (optional)		All	9/32" (7.0mm) thru 3/8" (9.5mm) dia. x 3/8" (9.5mm) deep, door face opposite to closer

Closer Adjustments

Use provided hex wrench to turn valves. NEVER force valves out of closer. NEVER completely close backcheck valve. Door must be open to adjust spring closing power. Refer to the chart.

Use of a power drill will void the Warranty.

Spring Closing Power			Number of Turns Required
	٦٢	Turnet		Maximum Door Size
	Door	Type of Installation	34" (0.85M)	36" (0.90M)	40" (1.00M)	44" (1.10M)	48" (1.20M)
1601	Interior	Regular Arm Top Jamb	urns	2	4	6	10	12
		Parallel Arm	Full 360° Tu	3	5	8	11	14
	Exterior	Regular Arm Top Jamb		3	5	8	11	14
		Parallel Arm		5	8	11	16	19
*30 Full (360°) turns maximum available = turns as shipped

Pinion Cap or Cover

Do not over tighten cap or cover screws.

1600SS Regular Arm Installation (Right Hand Shown)

1. Prepare door and frame.

2. Mount closer to door.

3. Take arms apart at elbow and choose arm placement in shoe and install arms.

4. Install separate arms. 5. Connect arms and adjust connection rod length to set arm elbow 90° to face of the door.

The 1600SS Non Hold Open Closer - Regular Arm has now been installed.

Go to page 2 for closer adjustments and decorative cap or cover installation.

3

1600SS Top Jamb Arm Installation (Right Hand Shown)

1. Prepare door and frame.

Opening	Dimension "A"
to 100°	7-1/2 (191)
101° to 120°	6 (152)
*121° to 180°	3-1/2 (89)
*Door/Wall/Hardware/Jamb conditions permitting

2. Mount closer to frame.

3. Take arms apart at the elbow and choose arm

4. Install separate arms. 5. Connect arms and adjust connection rod length to set arm elbow 90° to face of the door.

The 1600SS Non Hold Open Closer - Top Jamb Mount has now been installed.

Go to page 2 for closer adjustments and decorative cap or cover installation.

1600SS Parallel Arm Installation (Right Hand Shown)

1. Prepare door and frame.

Door Opening	Dimension "A"	Dimension "B"	Dimension "C"
to 100°	9-1/4 (235)	7-5/8 (194)	8-5/8 (219)
101° to 130°	7-3/4 (197)	6-1/8 (156)	7-1/8 (181)
*131° to 180° | 5-3/4 (146) | 4-1/8 (105) | 5-1/8 (130)
*Door/Wall/Hardware/Jamb conditions permitting

2. Close latch and sweep valves.

3. Install soffit plate and mount closer.

4. Take arms apart at elbow.

to soffit plate.

5. Remove arm shoe and install forearm | 6. Place main arm on closer spindle and rotate

1600SS Parallel Arm Installation (Right Hand Shown) cont.

7. Remove arm and attach as shown. 8. Open latch and sweep valves.

9. Connect arms and adjust connecting rod length to set arm elbow about 1-1/2" (38mm) from door. 1st

The 1600SS Non Hold Open Closer - Parallel Arm Mount has now been installed.

Go to page 2 for closer adjustments and decorative cap or cover installation.

Technical Product Support: Monroe, NC 28112 USA Phone: 877.974.2255 ext: 2 Techsupport.NortonRixson@assaabloy.com

Norton Rixson is a brand associated with ASSA ABLOY Accessories and Door Controls Group, Inc., an ASSA ABLOY Group company. Copyright © 2019, 2020, 2022, ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole or in