Norton Rixson 1600 Series Door Closeer, 1600H, Tri-Style Hold Open Installation Instructions_80-9316-3532-020

Open the original PDF document

1600H Series Non-Handed Door Closer

Arm Models 1601H, 1603BC-H, and 1604BC-H

Installation Instructions

Hold Open arm models, adjustable size 1-6 (model 1601H &) and size 3 & 4 (models 1603BC-H and 1604BC-H).

/ WARNING

This product can expose you to lead which is known to the state of California to cause cancer and birth defects or other reproductive harm.

For more information go to: www.P65warnings.ca.gov.

READ AND FOLLOW ALL INSTRUCTIONS. SAVE THESE INSTRUCTIONS.

NOTE: Legacy FHO arm has installation orientation. Refer to document number 80-9300-0003-000 for details.

1600H Series Non-Handed Door Closer

ATTENTION:

An incorrectly installed or improperly adjusted door closer can cause property damage or personal injury. These installation instructions should be followed to avoid the possibility of misapplication or misadjustment.

For special applications, a separate door and frame preparation template is packed with these instructions. Use this instruction sheet for installation sequence and closer adjustments only.
Doors should be hung on ball bearing or anti-friction hinges.

A separate door stop is recommended.
Always consult door/frame manufacturer for fastener compatibility.
Door and frame must be properly reinforced.
Adjust closing time speed between 3 and 7 seconds from 90° to 0°.
These door closers should NOT be installed on exposed side (weather side) of exterior doors.
Dimensions are given in inches (millimeters).

Supplied Hardware

	Mounting Hardware	Door or Frame	Drill
	Closer, Holder Shoe, Holder, PA Bracket: 1/4-14 x 1-1/2 Oval Flat Head Self Drilling. Screw	Wood/Metal	3/16" (4.8mm) for wood
	Closer, Holder Shoe, Holder, PA Bracket: 1/4-20 x 3/4 Oval Flat Head Mach. Screw	Metal	Drill #7 (.201 dia. or 5.1mm) Tap 1/4-20
	H/O Shoe to Holder, PA Bracket: 1/4-20 x 1/2 Oval Flat Head Mach. Screw	All	N/A
	Closer: Sleeve Nut and Bolt (SNB) (optional)	Hollow Metal	9/32" (7.0mm) thru 3/8" (9.5mm) door face opposite to closer
	with 1/4-20 x 3/4 Oval Flat Head Mach. Screw (recommended)	Aluminum or Wood	3/8" (9.5mm) thru
December of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the st	Closer: Thru Bolt and Grommet Nut (TBGN) (optional)		9/32" (7.0mm) thru 3/8" (9.5mm) dia. x 3/8" (9.5mm) deep, door face opposite to closer

Closer Adjustments

Use provided hex wrench to turn valves. NEVER force valves out of closer. NEVER completely close backcheck valve. Door must be open to adjust spring closing power. Refer to the chart.

Spring Closing Power			Number of Turns Required
	5 T			Maximum Door Size
	Doc	Type of Installation	*	34" (0.85M)	36" (0.90M)	40" (1.00M)	44" (1.10M)	48" (1.20M)
1601	Interior	Regular Arm Top Jamb	Full 360° Turns	2	4	6	10	12
	Interior	Parallel Arm		3	5	8	11	14
	Exterior	Regular Arm Top Jamb		3	5	8	11	14
	Exterior	Parallel Arm		5	8	11	16	19
*30	*30 Full (360°) turns maximum available = turns as shipped						ipped

Pinion Cap or Cover

Do not over tighten cap or cover screws.

1600H Regular Arm Installation (Right Hand Shown)

1. Prepare door and frame.

4. Connect arms, preload spring, and tighten set screw.

5. Set Hold Open.

Keep door open in position until dial screw secures dial.

The 1600H Hold Open Closer - Regular Arm has now been installed.

Go to page 2 for closer adjustments and decorative cap or cover installation.

1600H Series Non-Handed Door Closer

1600H Top Jamb Arm Installation (Right Hand Shown)


to 100°	7-1/2 (191)
101° to 120°	6 (152)
*121° to 180°	3-1/2 (89)
*Door/Wall/Hardware/Jamb conditions permitting

A longer connecting rod is required for reveals greater than 3" (76mm) Reveal

2. Mount closer to frame.

3. Remove dial from Hold Open arm and install separate arms.

4. Connect arms, preload spring, and tighten set screw.

5. Set Hold Open.

Keep door open in position until dial screw secures dial.

The 1600H Hold Open Closer - Top Jamb Mount has now been installed.

Go to page 2 for closer adjustments and decorative cap or cover installation.

1600H Parallel Arm Installation (Right Hand Shown)

1. Prepare door and frame.

Door Opening	Dimension "A"	Dimension "B"	Dimension "C"
to 100°	9-1/4 (235)	7-5/8 (194)	8-5/8 (219)
101° to 130°	7-3/4 (197)	6-1/8 (156)	7-1/8 (181)
*131° to 180° 5-3/4 (146) 4-1/8 (105) 5-1/8 (130)
*Door/Wall/Hardware/Jamb conditions permitting