Glynn Johnson 81 Series Surface Overhead Holder Installation Instructions 101405

Open the original PDF document

View PDF

INST.81

Surface Overhead Holder Installation Instructions

OVERHEAD HOLDERS OR STOPS MUST BE INSTALLED BEFORE CLOSERS

  • 1. A. DETERMINE THE MOUNTING BEING USED FROM ILLUSTRATION BELOW.
    • B. SELECT MOUNTING GROUP NUMBER FROM CHART BELOW. MOST CONTINUOUS HINGES ARE GROUPED WITH 4 1/2" WIDE BUTT OR 4 1/2" SWING CLEAR HINGE.

CENTER HUNG

HINGE

C. USING THE MOUNTING GROUP NUMBER AND THE OVERHEAD HOLDER OR STOP SIZE AND THE DEGREE OF OPENING DESIRED, FIND "A" AND "B" DIMENSIONS FROM CHARTS STARTING ON PAGE 3. FOR DEAD STOP ADD 13/16" (21) TO THE "A" DIMENSION FROM THE CHART.

81 SERIES PLAN MOUNTING VIEW LH SHOWN

OFFSET PIVOT SWING CLEAR HINGE

DOOR
THICKNESS 		HINGE TYPE & STYLE MOUNTING
GROUP
1 3/8"
(35) 		3/4" OFFSET PIVOT 2
4" WIDE BUTT 2
4 1/2" WIDE BUTT 1
5" WIDE BUTT 1
1 3/4" 3/4" OFFSET PIVOT 1
(44) 4" SWINGCLEAR 1
4 1/2" SWINGCLEAR 2
5" SWINGCLEAR 2
CENTERHUNG PIVOT 3
4 1/2" WIDE BUTT 1
5" WIDE BUTT 1
2" 3/4" OFFSET PIVOT 1
(ຣັ້າ) 4 1/2" SWINGCLEAR 1
5" SWINGCLEAR 1
SOSS 220 1
CENTERHUNG PIVOT 3
4 1/2" WIDE BUTT 1
5" WIDE BUTT 1
3/4" OFFSET PIVOT 1
2 1/4 "
(57) 		4 1/2" SWINGCLEAR 1
5" SWINGCLEAR 1
SOSS 220 1
CENTERHUNG PIVOT 3

NOTES:

  • A. HOLLOW METAL FRAMES SHOULD BE PROPERLY REINFORCED WITH A 3/16"(5) MINIMUM THICKNESS BY 12" (305) MINIMUM LENGTH PLATE.
  • B. HOLLOW METAL DOORS SHOULD BE PROPERLY REINFORCED WITH A 3/16"(5) MINIMUM THICKNESS BY 2 1/2"(64) MINIMUM WIDTH PLATE.
  • C. STOP ONLY UNITS ARE PERMITTED ON MANY FIRE DOOR APPLICATIONS. HOWEVER, MECHANICAL HOLD-OPEN DEVICES THAT REQUIRE MANUAL RELEASE ARE NOT PERMITTED FOR USE ON ANY FIRE DOOR AS OUTLINED ON NFPABO (®) OR NFPAIOI (®). CONTACT GLYNN-JOHNSON OR YOUR LOCAL REPRESENTATIVE FOR ASSISTANCE.
  • D. DEAD STOP (DS) TEMPLATING MAY BE USED ON HOLD-OPEN AND STOP ONLY MODELS. THE DS POSITION IS REACHED WHEN THE SHOCK SPRING IS FULLY COMPRESSED. WHEN DS TEMPLATING IS USED, THE INITIAL DEGREE OF STOP WILL BE 5-7 DEGREES LESS THAN THE DS OPENING. FOR USE ON DOORS OPENING BACK-TO-BACK AGAINST A WALL OR OBSTRUCTION.

SCREW DET AILS
QTY WOOD METAL
JAMB 4 #14 × 1 1/2" FPHSMS 1/4"-20 × 3/4" FPHMS
DOOR 2 1/4"-20 x 1 1/4" OPHMS 1/4"-20 x 1 1/4" OPHMS
(STD) 2 1/4"-20 x 2 1/2"
SEX BOLTS 		1/4"-20 x 2 1/2"
SEX BOLTS

NOTE: DIMENSIONS IN () ARE MILLIMETERS

  • 2. A. LOCATE "B" DIMENSION ON THE STOP. NOTE THAT THE "B" DIMENSION IS MEASURED FROM THE CENTERLINE OF THE HINGE AS SHOWN.
    • B. FOR METAL FRAMES, USE A #7 DRILL AND A 1/4"-20 TAP IN 4 PLACES. FOR WOOD FRAMES, DRILL A 3/16" PILOT HOLE IN 4 PLACES. MOUNTING HOLES SHOULD BE PREPARED IN THE FIELD.

  • 3. A. LOCATE "A" DIMENSION ON THE DOOR. NOTE THAT THE "A" DIMENSION IS MEASURED FROM THE CENTERLINE OF THE HINGE AS SHOWN.
    • B. DRILL THE 3/8" (10) DIAMETER HOLES DOWN 1 5/8" (41) FROM STOP. MOUNTING HOLES SHOULD BE PREPARED IN THE FIELD.

  • 4. A. INSTALL JAMB BRACKET ON THE STOP.
    • B. INSTALL THE CHANNEL ON THE DOOR WITH THE SHOCK SPRING TOWARDS THE HINGE EDGE OF THE DOOR.

NOTE: DIMENSIONS IN () ARE MILLIMETERS

MOUNTING GROUPS 1 & 2 BI SERIES SURFACE OVERHEAD STOP & HOLDER CAUTION: "A" & "B" DIMENSIONS ARE MEASURED FROM THE CENTERLINE OF PIVOT, NOT EDGE OF DOOR FOR DEAD STOP ADD 13/16" (21) TO THE "A" DIMENSION HO=HOLD-OPEN FOR HOLDERS, OPENING FOR STOPS

DEGREE BS HO 90 HO 95 HO 27 I/16-33 9 3/16 8 15/16 8 5/8 8 3/8 8 1/8 77/8 898-991 338 227 219 15 1/8 17/8 12 1/8 18 1/16 325 892-1143 460 365 435 324 416 325 892-1143 460 365 20 5/8 15 1/8 11 3/16 11 3/16 12 3/4 416 325 811/16-39 13 1/2 11 3/4 12 3/4 11 12 3/16 10 7/16 893-991 343 298 324 279 309 265 893-116-45 11 1/4 12 3/4 11 12 3/16 10 7/16 13 1/16 14 3/18 11 1/16 16 3/16 11 1/16 11 3/14 11 12 3/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 11 1/16 1
| DIM | DOOR | A B A B B A B B A B B A B B A B B A B B A B B A B B A B B A B B A B B A B B A B A B B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B B A B B A B B A B B B B B B B B B B B B B B B B B B B B
| DEGREE | B5 HO | 90 HO | 95 HO | 100 HO | |
| DIM | DOOR | A B A B B A B B A B B A B B A B B A B B A B B A B B A B B A B B A B B A B B A B B A B B A B B A B A B B A B B A B A B B A B B A B B A B B A B B A B B A B B A B B A B B A B B A B B A B B A B B A B B A B B A B B A B B A B B A B B A B B A B B A B B A B B A B B A B B A B B A B B A B B A B B A B B A B B A B B A B B A B B A B B A B B A B B A B B A B B A B B A B B A B B A B B A B B A B B A B B A B B A B B A B B A B B A B B A B B A B B A B B A B B A B B A B B A B B A B B A B B A B B A B B A B B A B B A B B A B B A B B A B B A B B A B B A B B A B B A B B A B B A B B A B B A B B A B B A B B A B B A B B A B B A B B A B B A B B A B B A B B A B B A B B A B B A B B B A B B B B B B B B B B B B B B B B B B B B
| DIOM | DOOR | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B | A | B
| DEGREE | B5 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90 HO | 90
| DEGREE | B5 HO | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0 HC | B0
| DIM | DOOR | A B HO | B
DEGREE B5 HG DIM OPENING B13 mm 687-838 233 B14 mm 838-991 338 B15 mm 892-1143 460 B16 mm 114-1372 522 B17 iN 33 1/16-39 13 1/16 16 B18 mm 114-1372 522 B19 mm 839-991 343 B19 mm 839-991 343 B10 33 1/16-39 13 1/2 11 B11 33 1/16-39 13 1/2 11 B12 mm 839-991 343 B13 mm 839-991 343 B14 mm 839-991 343 B15 mm 839-991 343 B16 mm 839-991 343 B17 mm 839-991 343 B18 mm 839-991 343 B19 mm 839-991 343
B13 | DEGREE | B5 | B14 | DOODR | A | B15 | IN | 27 1/16-33 | 9 3/16 | B16 | IN | 33 1/16-39 | 13 5/16 | B17 | IN | 33 1/16-39 | 13 5/16 | B18 | IN | 39 1/16-45 | 17 15/16 | B19 | IN | 45 1/16-33 | 9 7/16 | B10 | IN | 27 1/16-33 | 9 7/16 | B11 | B87-838 | 240 | B12 | IN | 33 1/16-39 | 13 1/2 | B13 | IN | 33 1/16-39 | 343 | B14 | IN | 39 1/16-45 | 18 1/8 | B15 | IN | 39 1/16-45 | 18 1/8 | B16 | IN | 45 1/16-54 | 20 3/4 | B17 | B16 | IN | 45 1/16-54 | B18 | IN | 45 1/16-54 | 20 3/4 | B19 | IN | 45 1/16-54 | 20 3/4 | B19 | IN | 45 1/16-54 | 20 3/4 | B10 | IN | 45 1/16-54 | 20 3/4 | B10 | IN | 45 1/16-54 | 20 3/4 | B10 | IN | 45 1/16-54 | 20 3/4 | B10 | IN | 45 1/16-54 | 20 3/4 | B10 | IN | 45 1/16-54 | 20 3/4 | B10 | IN | 45 1/16-54 | 20 3/4 | B10 | IN | 45 1/16-54 | 20 3/4 | B10 | IN | 45 1/16-54 | 20 3/4 | B10 | IN | 45 1/16-54 | 20 3/4 | B10 | IN | 45 1/16-54 | 20 3/4 | B10 | IN | 45 1/16-54 | 20 3/4 | B10 | IN | 45 1/16-54 | 20 3/4 | B10 | IN | 45 1/16-54 | 20 3/4 | B10 | IN | 45 1/16-54 | 20 3/4 | B10 | IN | 45 1/16-54 | 20 3/4 | B10 | IN | 45 1/16-54 | 20 3/4 | B10 | IN | 45 1/16-54 | 20 3/4 | B10 | IN | 45 1/16-54 | 20 3/4 | B10 | IN | 45 1/16-54 | 20 3/4 | B10 | IN | 45 1/16-54 | 20 3/4 | B10 | IN | 45 1/16-54 | 20 3/4 | B10 | IN | 45 1/16-35 | 20 3/4 | B10 | IN | 45 1/16-35 | 20 3/4 | B10 | IN | 45 1/16-35 | 20 3/4 | B10 | IN | 45 1/16-35 | 20 3/4 | B10 | IN | 45 1/16-35 | 20 3/4 | B10 | IN | 45 1/16-35 | 20 3/4 | B10 | IN | 45 1/16-35 | 20 3/4 | B10 | IN | 45 1/16-35 | 20 3/4 | B10 | IN | 45 1/16-35 | 20 3/4 | B10 | IN | 45 1/16-35 | 20 3/4 | B10 | IN | 45 1/16-35 | 20 3/4 | B10 | IN | 45 1/16-35 | 20 3/4 | B10 | IN | 45 1/16-35 | 20 3/4 | B10 | IN | 45 1/16-35 | 20 3/4 | B10 | IN | 45 1/16-35 | 20 3/4 | B10 | IN | 45 1/16-35 | 20 3/4 | B10 | IN | 45 1/16-35 | 20 3/4 | B10 | IN | 45 1/16-35 | 20 3/4 | B10 | IN | 45 1/16-35 | 20 3/4 | B10 | IN | 45 1/16-35 | 20 3/4 | B10 | IN | 45 1/16-35 | 20 3/4 | B10 | IN | 45 1/16-35 | 20 3/4 | B10 | IN | EX 1/16-35 | 20 3/4 | B10 | EX 1/16-35 | 20 3/4 | B10 | EX 1/16
DIM OPENING BI3 mm 687-838 BI4 mm 687-838 IN 33 1/16-39 IN 39 1/16-45 IN 39 1/16-54 IN 45 1/16-33 IN 27 1/16-33 IN 45 1/16-33 IN 33 1/16-33 IN 33 1/16-39 IN 33 1/16-39 IN 33 1/16-39 IN 33 1/16-45 IN 39 1/16-45 IN 39 1/16-45 IN 39 1/16-45 IN 39 1/16-45 IN 39 1/16-54
815 818 818 818 818 818 818 818 818 818

MOUNTING GROUP 3 81 SERIES SURFACE OVERHEAD STOP & HOLDER CAUTION: "A" & "B" DIMENSIONS ARE MEASURED FROM THE CENTERLINE OF PIVOT, NOT EDGE OF DOOR FOR DEAD STOP ADD 13/16" (21) TO THE "A" DIMENSION HO=HOLD-OPEN FOR HOLDERS, OPENING FOR STOPS

1 DEGREE 85 HO НО 06 90 HO 0H 9 6 НО 100 100 HO 105 105 HO 1 1 ( 110 HO
DIM DOOR ٧ В ∀ В ٧ В ٧ В ∢ В V В
V 013 IN |33 1/16-39 |9 15/16 |9 11/ 912/16 16 9 3/8 9 1/16 8 13/16 8 11/16 8 11/16 8 1/2 8 1/4 | 7 13/16 7 13/16 7 7/8 91/6 / 91/81 / 7 9/16
IOUI n
0 		E B39-991 253 246 240 230 224 221 220 210 206 200 198 192
I TV IN 39 1/16-45 14 12 1/4 12 1/4 13 1/4 11 1/2 12 9/16 10 13/16 12 3/16 11 1/2 12 9/16 10 13/16 12 3/16 10 7/16 11 3/4 11 3/4 10 11 3/8 8/9 6
NG NG
P 		E 992-1143 360 31.1 340 262 319 275 309 265 298 254 290 244
GR GR IN 45 1/16-51 18 5/8 15 1/16 17 3/4 14 3/16 17 1/16 13 1/2 16 3/8 16 17 3/4 14 3/16 17 1/16 13 1/2 16 3/8 12 13/16 15 3/4 12 3/16 15 3/4 12 3/16 15 3/8 11 13/16
OUF 710 Æ 114-1295 473 383 451 09E 433 343 420 325 400 310 390 300
> # ) # IN 51 1/16-57 21 3/16 16 11, 21 3/16 /16 20 1/4 15 3/4 15 3/4 19 7/16 14 15/16 18 3/4 14 15/16 18 3/4 14 1/4 18 1/8 18 1/8 91/1 EI 91/E 81 8/5 E1 18 3/16 13 1/16
3 0.10 mm 1296-1448 540 424 514 400 493 379 476 362 460 346 462 332

ALLEGION

DIMENSIONS IN () ARE IN MILLIMETERS NOTE:

INST.81