INST.100

Concealed Overhead Holder Installation Instructions

OVERHEAD HOLDERS OR STOPS MUST BE INSTALLED BEFORE CLOSERS

• 1. A. DETERMINE THE MOUNTING BEING USED FROM ILLUSTRATION BELOW.
  • B. SELECT MOUNTING GROUP NUMBER FROM THE CHART BELOW. MOST CONTINUOUS HINGES ARE GROUPED WITH 4 1/2" WIDE BUTT OR 4 1/2" SWING CLEAR HINGE.
  • C. USING THE MOUNTING GROUP NUMBER AND THE OVERHEAD HOLDER OR STOP SIZE AND THE DEGREE OF OPENING DESIRED, FIND "A", "B", "C", "D", AND "E" DIMENSIONS FROM CHART ON PAGE 3. FOR DEAD STOP ADD 9/16"(14) TO THE "A" DIMENSION FROM THE CHART. SEE NOTE D FOR INFORMATION ABOUT DEAD STOP.

NOTES:

• A. HOLLOW METAL FRAMES SHOULD BE PROPERLY REINFORCED WITH A 3/16"(5) MINIMUM THICKNESS BY 12"(305) MINIMUM LENGTH PLATE.
• B. HOLLOW METAL DOORS SHOULD BE PROPERLY REINFORCED WITH A 3/16"(5) MINIMUM THICKNESS PLATE.
• C. STOP ONLY UNITS ARE PERMITTED ON MANY FIRE DOOR APPLICATIONS. HOWEVER, MECHANICAL HOLD-OPEN DEVICES THAT REQUIRE MANUAL RELEASE ARE NOT PERMITTED FOR USE ON ANY FIRE DOOR AS OUTLINED ON NFPABO (**) OR NFPAIO! (**). CONTACT GLYNN-JOHNSON OR YOUR LOCAL REPRESENTATIVE FOR ASSISTANCE.
• D. DEAD STOP (DS) TEMPLATING MAY BE USED ON HOLD OPEN, FRICTION AND STOP ONLY MODELS, BUT SHOULD NOT BE USED ON "SE" MODELS. THE DS POSITION IS REACHED WHEN THE SHOCK SPRING IS FULLY COMPRESSED. WHEN DS TEMPLATING IS USED, THE INITIAL DEGREE OF STOP WILL BE 5°-7° LESS THAN THE DS OPENING. FOR USE ON DOORS OPENING BACK-TO-BACK, AGAINST A WALL OR OBSTRUCTION.

100 ADJUSTMENTS:

HOLD-OPEN TENSION ADJUSTMENT (HOLD-OPEN UNIT ONLY)-USING A 1/8" BALL END ALLEN WRENCH, TURN SCREW SHOWN IN BOTTOM OF CHANNEL CLOCKWISE TO INCREASE HOLD-OPEN TENSION AND COUNTERCLOCKWISE TO DECREASE HOLD-OPEN TENSION.

FRICTION TENSION ADJUSTMENT (FRICTION UNIT ONLY) - USING A 1/8" ALLEN WRENCH, HOLD SCREW SHOWN IN PLACE WHILE USING A 7/16" WRENCH TO TURN JAMB NUT COUNTERCLOCKWISE UNTIL LOOSE. TURN SCREW CLOCKWISE TO INCREASE FRICTION TENSION AND TURN COUNTERCLOCKWISE TO DECREASE THE FRICTION TENSION.

WHILE HOLDING THE SCREW IN PLACE, TURN THE JAMB NUT CLOCKWISE UNTIL TIGHT.

DIMENSIONS IN	(	)	ARE	ΙN
MILLIMETERS	`	_

DOOR THICKNESS	HINGE TYPE & STYLE	MOUNTING GROUP
	4" WIDE BUTT	2
	4 1/2" WIDE BUTT	2
	5" WIDE BUTT	1
1 3/4"	3/4" OFFSET PIVOT	2
(44mm)	4" SWINGCLEAR	1
	4 1/2" SWINGCLEAR	2
	5" SWINGCLEAR	2
	CENTERHUNG PIVOT	3
	4 1/2" WIDE BUTT	2
	5" WIDE BUTT	1
2"	3/4" OFFSET PIVOT	1
(51mm)	4 1/2" SWINGCLEAR	2
	5" SWINGCLEAR	2
	S0SS 220	2
	CENTERHUNG PIVOT	3
	4 1/2" WIDE BUTT	2
	5" WIDE BUTT	1
2 1 / 4 77	3/4" OFFSET PIVOT
2 1/4" (57mm)	4 1/2" SWINGCLEAR	1
	5" SWINGCLEAR
	SOSS 220	2
	CENTERHUNG PIVOT	3

SCREW DETAILS
	QTY	WOOD	METAL
DOOR	2	#18 × 3" PPHWS	5/16"-18 x 1 1/2" PPHMS
JAMB	4	#14 × 1 1/2" FPHSMS	1/4"-20 x 3/4" FPHMS

• 2. A. LOCATE "B" DIMENSION ON THE FRAME. NOTE THAT THE "B" DIMENSION IS MEASURED FROM THE CENTERLINE OF THE HINGE AS SHOWN.
  • B. MORTISE FOR THE JAMB BRACKET AS SHOWN. REFER TO LEFT AND RIGHT HAND PLAN VIEWS FOR APPROPRIATE HOLE PATTERN.
  • C. FOR METAL FRAMES, USE A #7 DRILL AND A 1/4"-20 TAP IN 4 PLACES. FOR WOOD FRAMES, DRILL 3/16" PILOT HOLE IN 4 PLACES.

REFER TO ILLUSTRATION BELOW AND ON SHT 1 FOR THE FOLLOWING NOTES:

• 3. A. LOCATE "A" AND "D" DIMENSIONS ON THE CENTERLINE OF THE DOOR. NOTE THAT THE "A" DIMENSION IS MEASURED FROM THE CENTERLINE OF THE HINGE AS SHOWN.
  • B. MORTISE FOR THE CHANNEL AS SHOWN IF REQUIRED. FOR 100H HOLD-OPEN VERSION, MORTISE FOR HOLD-OPEN LOCK MECHANISM AND DRILL 5/8" (16) DIAMETER HOLE FOR CONTROL KNOB AS SHOWN. (WHEN HP HOLD-OPEN, F FRICTION OR S STOP UNIT IS SUPPLIED, ADDITIONAL MORTISE FOR HOLD-OPEN MECHANISM AND CONTROL KNOB ARE NOT REQUIRED.)
  • C. LOCATE "C" AND "E" DIMENSIONS ON THE TOP OF THE DOOR. NOTE THAT THE "C" DIMENSION IS MEASURED FROM THE CENTERLINE OF THE HINGE AS SHOWN.
  • D. MORTISE FOR ARM CUTOUT AS SHOWN.
  • E. FOR METAL DOORS, USE A F DRILL AND 5/16-18 TAP IN 2 PLACES. FOR WOOD DOORS, DRILL 1/4" PILOT HOLES IN 2 PLACES. MOUNTING HOLES SHOULD BE PREPARED IN THE FIELD.

• 4. A. INSTALL THE CHANNEL IN THE DOOR WITH THE SHOCK SPRING TOWARDS THE HINGE EDGE OF DOOR.
  • B. INSTALL JAMB BRACKET IN FRAME.
  • C. FOR 100H HOLD-OPEN VERSION ONLY, EPOXY (NOT PROVIDED) EYELET IN 5/8" (16) HOLE.
  • D. FOR 100H HOLD-OPEN VERSION ONLY, PLACE SERRATED KNOB AND KNOB SPACER OVER CAP SCREW AS SHOWN. THREAD ASSEMBLY THROUGH 5/8" (16) HOLE IN DOOR ONTO LOCK.

DIMENSIONS IN ( ) ARE IN MILLIMETERS

MOUNTING GROUPS 1, 2 & 3 100 SERIES CONCEALED OVERHEAD STOP & HOLDER

CAUTION: "A", "B", & "C" DIMENSIONS ARE MEASURED FROM THE CENTERLINE OF PIVOT, NOT EDGE OF DOOR

	ı	10	254	12	305	15 3/4	400	20	508	26	099	32	813	10	254	12	305	15 3/4	400	20	508	56	980	35	813	10	254	12	305	15 3/4	400	50	508	56	990	32	813
	а	14 3/8	365	15 1/2	394	16 3/4	425	17 3/4	451	19 3/4	205	21 1/4	533	14 3/8	392	15 1/2	394	16 3/4	425	17 3/4	451	19 3/4	205	21 1/4	533	14 3/8	365	15 1/2	394	16 3/4	425	17 3/4	451	19 3/4	502	21 1/4	533
	Ш					18	457	22 1/4	565	28 1/4	718	34 1/4	870			15 3/4	400	18*	457	22 1/8	295	28 1/8	714	34 1/4	870			-		18	457	22 1/4	565	28 3/8	721	34 3/8	873
무	υ	-				2 11/16*	88	3 7/16	87	4 13/16	122	5 11/16	144			-	25	2 7/8*	73	3 5/8	82	5	127	5 13/16	148	-			-	3 1/2	88	4 3/16	106	5 9/16	141	6 7/16	164
9	6			-		4 3/16*	106	4 15/16	125	6 5/16	160	7 3/16	183		-	3 1/2	89	4 3/8*	111	5 1/8	130	6 1/2	165	7 5/16	186	-	-	-	-	5	127	5 11/16	144	7 1/16	179	7 15/16	202
	٧		,	-		6 1/2*	165	10 1/2	267	15 7/8	403	2/1 1/2	546	-	-	3 5/16	84	*91/11 9	170	10 5/8	270	91	406	21 11/16	551	-		-	-	7 5/16	186	11 5/16	287	16 3/4	425	22 3/8	568
	ш		,	15 1/2	394	17 7/8	454	22 1/4	565	28 1/4	718	34 1/4	870	-		15 3/4	400	18*	457	22 1/8	295	28 1/4	718	34 1/4	870	-	,	-		18	457	22 1/4	565	28 1/4	718	34 3/8	870
오	c		,	1	ξ2 Ε	2 15/16*	75	3 5/8	85	5 1/16	129	91/1 9	154	-	-	-	25	3 1/16*	78	3 7/8	86	5 1/4	133	6 3/16	157	-		-	-	3 3/4	92	4 1/2	411	5 15/16	151	6 15/16	176
195	8			3 1/2	88	4 7/16*	113	8/1 9	130	9/16	167	7 9/16	192			3 11/16	94	4 9/16*	116	5 3/8	137	6 3/4	171	91/11 2	195	-		-	-	5 1/4	133	9	152	7 7/16	189	8 7/16	214
	*		,	3 1/4	83	3 11/16*	170	10 3/4	273	16 3/16	411	21 7/8	556			3 1/2	68	6 15/16	176	10 7/8	276	16 3/8	416	22 1/16	560				-	7 9/16	192	11 9/16	294	17 1/16	433	22 3/4	578
	Е			15 1/2	394	18	457	22 1/4	565	28 1/4	718	34 1/4	895	13 3/4	349	15 3/4	400	18*	457	22 1/8	295	28 1/4	718	34 1/4	870	-		-	-	18	457	22 1/8	295	28 1/4	718	34 3/8	5
오	٥			1 1/4	35	3 1/8	79	3 15/16	100	5 1/2	140	6 7/16	164	0	0	1 1/4	32	3 5/16*	84	4 3/16	106	5 11/16	144	8/5 9	168	-		-	-	4	102	4 7/8	124	6 5/16	160	7 5/16	186
8	60			3 11/16	94	4 5/8*	117	5 7/16	138	7	178	7 15/16	202	Э	9/	3 15/16	100	4 13/16*	122	5 11/16	144	7 3/16	183	8/18	206	-				5 1/2	140	8/8 9	162	7 13/16	198	8 13/16	224
	<			3 7/16	87	6 15/16	176	=	279	16 9/16	421	22 5/16	567	1 15/16	49	3 11/16	94	7 1/8*	181	11 3/16	284	16 3/4	425	2/1 22	572	-	,	-	-	7 3/16	198	11 7/8	302	17 7/16	443	23 1/4	591
•	ш	13 3/4	348	15 1/2	394	17 7/8	454	83	559	28 1/8	714	34 1/8	864	14	356	15 3/4	400	17 7/8	454	22	559	82	711	34 1/4	870	-	,	-	-	17 3/4	451	22 1/8	295	28 1/4	718	34 1/8	198
오	υ	0	0	1 1/2	38	3 9/16	06	4 7/16	113	6 1/16	154	7 1/8	181	0	0	1 1/2	98	3 3/4	92	4 5/8	117	6 1/4	159	7 3/16	183	-		-	-	4 1/2	114	5 5/16	135	8// 9	175	8	203
დ -	10	е	76	3 15/16	100	4 15/16	125	5 13/16	148	7 7/16	189	8 1/2	216	3 3/16	18	4 1/16	103	8/1 9	130	9	152	7 5/8	194	8 9/16	217	-		-	-	2 7/8	147	6 11/16	170	8 1/4	210	9 3/8	238
-	<	1 7/8	48	3 11/16	94	7 1/4	184	11 5/16	287	17	432	22 3/4	578	2 1/16	25	3 7/8	86	7 7/16	189	11 1/2	282	17 1/8	435	R	584	-			-	8/18	208	12 1/4	311	17 15/16	456	23 3/4	603
	ш	14	356	15 1/2	394	17 7/8	454	22 1/8	295	28 1/8	714	34 1/8	867	14	356	15 3/4	400	17 7/8	454	22 1/8	295	82	711	34 1/4	864	-		-		17 7/8	454	8/1 22	295	28 1/8	714	34 1/8	867
오 .	O	0	0	1 3/4	44	3 7/8	86	4 3/4	121	6 1/2	165	7 5/8	194	0	0	1 3/4	44	4 1/16	103	4 15/16	125	6 3/4	171	1 7/8	200	-		-	-	4 3/4	121	5 11/16	144	7 1/2	191	8 2/8	219
8 .	æ	3 3/16	18	4 1/8	105	5 1/4	133	6 1/8	156	7 7/8	200	6	229	3 7/16	87	4 3/8	111	5 7/16	138	6 5/16	160	8/18	206	9 1/4	235	-	-	-	-	8/1 9	156	7 1/16	179	8 1/8	225	10	254
	<	2 1/16	25	3 15/16	9	7 9/16	192	11 11/16	297	17 7/16	443	23 3/8	594	2 5/16	59	4 1/8	105	7 3/4	197	11 7/8	302	17 5/8	448	23 1/2	597	-	-	-	-	8 1/2	216	12 11/16	322	18 7/16	468	24 3/8	619
	ш	4.	356	15 1/2	394	17 7/8	454	23	559	28 1/8	714	34 1/8	867	14 1/2	368	15 3/4	400	17 7/8	454	22	559	8/1 82	714	34 1/4	870	-		-	-	17 3/4	451	8/1 22	295	8/1 82	714	34 1/8	B67
오	υ	0	0	2	51	4 1/4	108	5 1/4	133	7 1/16	179	8 5/16	211	0	0	2	51	4 7/16	113	5 7/16	138	7 5/16	186	8 7/16	214				-	5 1/4	133	6 1/4	159	8 1/16	205	9.3/8	238
B.	10	3 7/16	87	4 1/2	1.4	5 5/8	143	8/9 9	168	8 7/16	214	91/11 6	246	31/11 €	94	4 5/8	117	5 13/16	148	6 13/16	173	8 11/16	221	91761 6	249		1			8/5 9	168	1 5/8	194	9 7/16	240	10 3/4	273
	<	2 5/16	29	4 1/4	108	7 15/16	202	12 1/8	308	18	457	24	610	2 9/16	92	4 7/16	113	8/18	206	12 5/16	313	18 1/4	484	24 1/4	676				-	8 1/8	225	13 3/16	335	19 1/16	484	25 1/16	637
DEGREE	DOOR OPENING	18-23 */	457-584 •/	IN. 23 1/16-27*	585-686	27 1/16-33	687-838	33 1/16-39	839-991	39 1/16-45	992-1143	45 1/16-54	1144-1372	18-23 */	457-584 */	23 1/16-27*	585-686	27 1/16-33	687-838	33 1/16-39	839-991	39 1/16-45	992-1143	45 1/16-54	1144-1372	18-23 */	457-584 *1	£3 1/16-27•	585-686 •	33 1/16-39	839-991	39 1/16-45	992-1143	45 1/16-51	1144-1295	51 1/16-57	1296-144B
DEG .	D IM.	ż	Æ		200 E	ż	- WE	ĸ.	mm 85	IN. 39	шш	IN. 45	E	N	E	.N. 23	Ē	N.	39 ww	ï.	mm 83	ĸ	66 ww	N	mm 114	.NI	E	IN. 23	E E	Ν̈́	. mm 83	ĸ.	40 mm 98	IN. 45	æ	ż	Ę
		E.		2	-			GRO	_	-	:		2	-	-		-			GROU	- 1		۲		3	2	:	2	•	_	-	_	ġ IUP		2		90

* NOT TO BE USED WITH OFFSET PIVOTS / NOT TO BE USED WITH SWINGCLEAR HINGES FOR DEAD STOP ADD 9/18" (14) TO THE "A" DIMENSION 'FOR SE STOPS USE HOLD-OPEN MOUNTING DIMENSIONS 'HO-HOLD-OPEN FOR HOLDERS, OPENING FOR STOPS IS-ARM LENGTH FROM PIVOT CENTERLINE (FOR REFERENCE ONLY)

DIMENSIONS IN ( ) ARE MILLIMETERS. NOTE: